Effective Installation Techniques for Vibrating Fork Level Switches in Vertical Pipelines

Vibrating fork level switches are reliable and perfect for overfill prevention, high and low level alarm and pump protection even in the most challenging of applications, such as water conservancy, chemical, environmental protection, food, medicine and other industrial fields. Vibrating fork level switches have no moving parts, needs no calibration and is virtually unaffected by process conditions. Vibrating fork level switches are ideal for pipeline liquid level measurement because of its compact tines. Horizontal pipeline is common and easy to install, but what are the installation skills for vertical pipeline?

Effective Installation Techniques for Vibrating Fork Level Switches in Vertical Pipelines
The Ring-11 Fork Level Switches measure the liquid level of pure water in a high-pressure environment of 50 bar

Difficulties in Liquid Level Measurement of Vertical Pipeline

  1. Fast liquid velocity;
  2. Liquid is supplied intermittently, and with many bubbles and foams;
  3. Narrow space around the pipeline limits the installation position and the method of measuring sensor;
  4. High pressure in the vertical pipe has great impact on instrument.

Advantages of Ring-11 Liquid Level Switch

On basis of the high requirements for liquid level measuring instruments to the working conditions of vertical pipeline, Ring-11 Liquid Level Switch is the ideal choice.

Ring-11 Liquid Level Switch is a high reliability control switch specially used for liquid level measurements. The excellent, stable and reliable performance and quality are comparable to imported peers.

Based on the fork resonant principle, when a fork vibrates in harmonic resonance comes in contact with measured liquid, its vibrating frequency will greatly decrease. The fork’s harmonic resonant frequency has been precisely pre-adjusted to achieve high sensitivity so the lowest measurable density can be as low as 0.5g/cm³, and can withstand the pressure of 64bar. Jiwei Ring-11 liquid level switch is excellent in level measurement for acids like HCL, H₂SO₄, H₂SO₃, and alkali liquids, syrup, medical liquids, industrial wastewater, etc. And particularly, it is suitable for pressured liquefied gas (such as LNG) and applications under complicated working conditions where measured liquid is easy to foaming, bubbling or with high viscosity and under vibration disturbance environment etc.

Effective Installation Techniques for Vibrating Fork Level Switches in Vertical Pipelines
Vertical pipelines

Ring-11 Liquid Level Switch has passed SIL2 / SIL3 Functional Safety Assessment, as well as certified for both Intrinsic Safety and Flameproof Enclosure explosion protection. Four optional outputs: relay output, two-wire system, NAMUR and transistor.

Installation Skills for Vertical Pipeline

Installation methodⅠ

Effective Installation Techniques for Vibrating Fork Level Switches in Vertical Pipelines
Figure 1

As shown in Figure 1, a water storage tank is equipped laterally. To ensure the water enter into water storage tank, a welded water diversion plate is also equipped. A return tube is opened at the lower part of the water storage tank to facilitate the water return to vertical pipe. The diameter of the return tube is d, the size should be determined based on the size of water storage tank, so that when water enters the water storage tank, it can quickly dip to the tines; when no water in the pipe, the water in water storage tank can quickly return to the vertical pipe, so that the liquid level of the water storage tank and the vertical pipe is basically the same.

Installation method Ⅱ

As shown in Figure 2, the vertical pipe leads out a side pipe with a matching flange of the sensor. The sensor is also equipped with U-groove as the sketch in Figure 2. The radius of U-groove is about 20 mm with thickness of 1 mm. It is cut by a round tube and welded on the flange of sensor. The total length of U-groove should be longer than the tines’ length. The length of extension part L1 is about 10 mm, and the end of U-groove should extend into the vertical pipe as L2. The length of L2 is about 10 ~ 20 mm, and the plugging height at the end of U-groove is aligned with the lower part of tines. The specific size of the U-groove should be determined by the size of the pipe as well as the installation position, and the opening of the U-groove should face up to the flow direction.

Effective Installation Techniques for Vibrating Fork Level Switches in Vertical Pipelines
Figure 2

The design principle is to make the baffle at the end of U-shaped groove blocks the liquid in U-groove. When liquid flows down the vertical pipe, it rises the liquid level in U-groove and immerses the tines, so the sensor sends out an alarm signal. When no liquid flows down the vertical pipe, the liquid is blocked by the baffle, so the tines will not immersed by liquid.

These two installation methods can skillfully avoid the installation difficulties of vertical pipeline. The tines are free from the direct impact of liquid, and the liquid level from the tines is basically synchronized with the liquid level in the vertical pipeline, which can ensure that the monitoring signal is consistent.

相关新闻

SHARE
TOP